All DLM circuit board designs come bare and the holes are not drilled. A sheet of instructions and a parts list is provided. A kit version of these boards are also offered that will include enough electronic parts to get you started in lighting up your model starship. Typically the prices with the electronics parts will nearly double the bare board prices. The builder has many options on how to get it mounted in the model and how it is powered and hooked up. So batteries, power supplies, conectors, wires and extra LEDs are not included. A lot of these parts can be found at your local Radio Shacks or electronics supply store. It is also DLM Parts recommendation to use parts from Didgi-key.com. They are promt, consistantaly work, always in stock and the primary standard source for all DLM circuitry board prototypes.
TEMPORARY OUT OF STOCK... Please write to resereve your set to don@dlmparts.com
Smaller 2X/1000 Circuit Board
Welcome to Adobe GoLive 5
FEDERATION FLASHER BOARD 2X/1000 FFB 2X/1000 Circuit Board for smaller scale Star Ships (1/1000) A smaller circuit board of the FFB Blink and Flash Circuits that takes up a lot less space than the original FFB circuit. A 2 X 2 area with a low profile 1/2 inch hieght.
Powered by one 555 timer for blinking primary hull lights in red, green, and white and a LM3909 circuit that will flash bright white LEDs like a strobe light for anti collision lights on Warp Nacelles and above the Bridge. The circuit works well with voltages between 4.5 to 6 volts.
The ideal use with this smaller circuit set up is with the smaller popular scale 1/1000 Federation Class type star ships as seen in the movies.
Polar Lights R2 Refit Enterprise,
AMT USS Excelsior,
AMT USS Enterprise NCC-1701-B
It will also work with a lot of science fiction models with special effects lighting. Very adaptable for many model lighting options and fits in a smaller space
$10.00 for the bare board includes instruction sheet and parts list
DLM-06.53 FFB 2X/1000 $10.00
You will also need wire, power connecters, soldure and a solduring iron, LEDs of your choice and power supplies. Instructions and parts list included. See illustrations below.
LM3909 LED flasher Chip
The LM3909 and or IC876 is obsolete and getting hard to find. However I have a modest but finite inventory of the LM3909 chips. See below for ordering the chip and parts for the FFB circuit board. DLM--6.51 LM3909 LED Flasher Chip $5.00
FEDERATION FLASHER BOARD Kit with Electronic Components
DLM also offers a FFB 2X/1000 Circuit kit with all the resisters, capacitors and IC chips to get you started with assembly. Included is one each of Red, Green, and five (5) White 3mm LEDs, One foot length of 10 stranded ribon wire, with parts supplied by Digi-Key Electronics. Just enough to get your operating lights on the Refitted USS Enterprise Star Ship . You will also need to obtain hook up wires, power supplies, additional LEDs, soldure and solduring iron.
FFB 2X/1000 Circuit Board Basic kit with parts, LEDs and wire cable DLM-6.54 FFB 2X/1000 circuit kit $35.00
FFB 2x/1000
FFB 2x/1000 kit with parts, LED and wire
TEMPORARY OUT OF STOCK... Please write to resereve your set to don@dlmparts.com
Welcome to Adobe GoLive 5
FEDERATION FLASHER BOARD:
Powered by one 555 timer for blinking primary hull lights in red, green,yellow and white and a LM3909 circuit that will flash bright white LEDs like a strobe light for anti collision lights on Warp Nacelles and above the Bridge. Ideal use is with the AMT/ERTL Refit Enterprise and Reliant type star ships as seen in the movies. It will also work with lighting up the new Polar Lights 1:350 scale USS Enterprise
The LM3909 and or IC876 is obsolete and getting hard to find. However I have a modest but finite inventory of the LM3909 chips See below for ordering the chip and parts for the FFB circuit board
$15.00 for the bare board. $15.00DLM-06.5 Federation Flasher Board
You will also need wire, power connecters, soldure and a solduring iron, LEDs of your choice and power supplies. Instructions and parts list included. See illustration bleow.
LM3909 LED flasher Chip
$5.00 DLM--6.51 LM3909 LED Flasher Chip
FEDERATION FLASHER BOARD Starter Kit with Electronic Components
The DLM alos offers a FFB starter kit with all the resisters, capacitors and IC chips to get you started with assembly. Included is one each of red, green, yellow and two (2) white 3mm LEDs with parts supplied by Digi-Key Electronics. Just enough to get you started on assembly of your Star Ship lighting project. You will also need to obtain ribbon cable or hook up wires, power supplies additional LEDs, soldure and solduring iron.
FFB Circuit Board Starter kit with parts
$35.00 DLM-6.52 FFB Starter kit
FEDERATION FLASHER / BARE
FFB circuit with Parts
FED FLASHER IN OPERATION
Fed Flasher Board installed in Ambassador Class
Click on this image to see the instruction sheet
LED BLINKER BARE BOARD
Welcome to Adobe GoLive 5
SIMPLE LED BLINKER: Powered by a IC 555 timer circuit
$5.00 bare board only. DLM-34 Simple LED Blinker Bare Board
Board with electronic parts including LEDs sold as kit $15.00 DLM-34.1 Simple LED Blinker Board and kit Includes capacitors, resisters, chips and enough LEDs including (1) Red and (1) Green to get you started. You will need wire, power connecters, soldure and power supplies.
KBOP LED BLINKER:
Klingon Bird of Prey Engine FX
The Simple LED board has been reconfigured to drive the engine on a Klingon BOP with completly different component values. It also fits into the AMT KBOP kit as a all in one bulkhead supporting 3 red LEDs... A flickering pulsed effect is achieved. Prebuildt and tested units are available Ask for this option before ordering.
DLM-35 Klingon Engine LED driver Bare Board
DLM-35.1 Klingon Engine LED driver Board KIT $15.00
Includes capacitors, resisters, chips and enough LEDs (3) Red . You will need wire, power connecters, soldure and power supplies.
KBOP Engine FX kit
A single lighting unit fits in AMT kit like a bulkhead.
